TGV Glass Wafer & Interposer Engineering Design Specifications for AI Packaging
TGV Glass Wafer & Interposer Engineering Design Specifications for AI Packaging
This engineering spec document defines design rules, material limits, metrology thresholds, process constraints and acceptance criteria for custom TGV glass wafers and glass interposers deployed in AI GPU, HBM chiplet, 2.5D and panel-level advanced packaging. Use this document together with your stack-up drawing, BOM and qualification plan for DFM review.
1. Base Glass Material Specifications
| Property | Alkali‑Free Aluminosilicate | Borosilicate |
|---|---|---|
| CTE (25–300°C) | 2.5 ~ 3.5 ppm/°C, silicon‑matched | 3.2 ~ 4.6 ppm/°C |
| Dielectric Constant @ 10GHz | 4.6 ~ 5.1 | 4.7 ~ 5.2 |
| Loss Tangent @ 10GHz | ≤0.0040 | ≤0.0055 |
| Recommended Use | HPC, AI GPU, CPO, high‑speed 224Gbps+ | Prototypes, temporary carriers, low‑frequency test vehicles |
Soda‑lime glass is not approved for high‑speed semiconductor packaging due to alkali ion migration and unstable high‑frequency performance.
2. Substrate Geometry & Thickness Rules
- Available form: Round wafer (100mm / 200mm / 300mm), custom square / rectangular panels
- Thickness range: 100 μm – 1000 μm; common production thickness: 200μm, 300μm, 500μm
- TTV (Total Thickness Variation): Standard ±5μm; tight spec option ±2μm for high‑density RDL
- Global warpage: Default ≤30μm for 300mm wafer; tighter limits available upon request for co‑packaged optics
- Surface finish: Double‑side optical polish; Ra ≤0.5nm for RDL process compatibility
3. TGV Via Design Rules
- Via diameter: 20μm minimum, up to 200μm; smaller vias require laser drilling process qualification
- Aspect ratio maximum: 10:1 (via depth : via diameter); higher ratios require separate process development
- Minimum center‑to‑center pitch: 50μm; tighter pitch needs DFM risk assessment
- Sidewall taper: 85°–90° preferred; tapered vias improve copper filling yield
- Metal stack: Dielectric liner + barrier layer + Cu fill; copper void target: 0% for qualification lots
4. RDL & Metallization Constraints
Our TGV platform supports single‑sided or double‑sided RDL redistribution after CMP planarization. Minimum line/space is process dependent; standard rule is 2μm / 2μm for qualified flows. Metal options: copper primary, with Ni/Au finish for probing or assembly. All metallization stacks must be defined in your drawing stack‑up before sampling. Seed layer adhesion testing is included in qualification build.
5. Thermal & Reliability Design Limits
- Thermal cycling range: -40°C to +125°C standard qualification
- Maximum sustained temperature: 300°C (short‑term assembly exposure)
- Glass is electrically insulating; thermal conductivity is low. Glass interposer does not function as a heat spreader. Thermal path must be implemented separately via TIM and heat sink.
- CTE mismatch control is the primary lever to suppress warpage under power cycling for large HBM‑integrated packages.
6. Metrology & Inspection Acceptance Criteria
- Geometry: TTV, warpage, via position offset, panel/wafer dimensional tolerance
- Via quality: X‑ray void inspection, sidewall crack screening, cross‑section sampling for qualification
- Electrical: 4‑point probe resistance, daisy‑chain continuity, isolation leakage test
- Surface: Laser particle scan, scratch & dig inspection, cleanliness for cleanroom assembly
- Deliverables: Batch inspection report, raw metrology data, cross‑section images for qualification runs
7. Process Build Phases for Qualification
We recommend phased builds to control risk: Phase 1: Bare polished glass blank inspection. Phase 2: Drilled TGV substrate, no metal fill. Phase3: Copper filled + CMP planarized TGV sample. Phase4: Full RDL patterned interposer. Phase5: Pre‑production lot with full reliability test. This staged flow avoids high tooling cost before geometry and material feasibility are confirmed.
8. Drawing & RFQ Required Documentation Checklist
- Stack‑up drawing with layer thickness, material and metallization stack
- Via array layout, diameter, pitch, aspect ratio
- Maximum allowed TTV, warpage, surface roughness
- Signal frequency target and electrical test requirements
- Acceptance criteria, sampling plan and reliability test matrix
- Quantity breakdown: prototype / qualification / production volume
Related TGV Glass Products
- Bare polished glass wafer
- Laser drilled TGV glass wafer
- Copper filled TGV glass interposer
- Temporary release glass carrier
- Glass core FC-BGA substrate
- CPO photonic TGV glass substrate
- TGV glass interposer selection guide
Submit Specs for DFM & Technical Quotation
Send your stack‑up, drawing and acceptance requirements. Our optical & semiconductor engineering team will return DFM feedback, identify design risks and provide formal pricing and lead time.
Submit Specs & Request Quote


